Amada Vipros 568
Turret Sleeving

Amada Vipros 568 at a glance

Era

1998

Tonnage

55 ton

Turret

Thick turret

Control

Fanuc 04PC

The Vipros line ran 1995–2005 and is out of production. These machines are young enough to be thoroughly capable and old enough to have real turret hours on them — the most common profile we are called to.

Where this machine is in its life

A Vipros 568 from 1998 sits in the sweet spot for restoration. It is old enough to have accumulated real turret wear, and modern enough that the rest of the machine has plenty of working life in it. Nothing about its capability has been superseded for most sheet metal work.

Shops running these machines are usually not looking to replace them — they are looking to stop scrapping parts.

How a Vipros 568 turret wears

At 55 tons, the Vipros 568 is in the heavy class, and that changes how the turret wears. Every stroke puts substantial force through the station bore. Wear here is driven by load rather than cycle count, and it tends to show first in the stations carrying the largest tools on the thickest material.

The tell is always the same: the fault stays with the station rather than following the tool. Move a tool that is producing bad parts to another station — if it runs clean there, the bore is worn, and new tooling will not change that. See holes out of round or burring on punched parts for the full diagnosis.

What sleeving a Vipros 568 involves

Each worn bore is machined to a precise oversize and a hardened USA-made steel sleeve is pressed in with an interference fit, restoring the station to Amada factory tolerance — typically within 0.0002″. Engineers travel to you; the Vipros 568 never ships. 2–3 days of downtime, typically $8,000–$25,000 depending on scope. After the first install your own maintenance staff can replace sleeves in future.

Set against $100,000–$500,000+ for a replacement machine — see sleeve or replace, including where replacing genuinely wins.

Is the Vipros 568 a thick or thin turret machine?

The Vipros 568 is a thick turret machine. Thick and thin describe the turret, not automatically the tooling — the two are quoted separately, and a machine has to be identified on both counts before sleeves or tooling are ordered.

Tonnage will not tell you either: several 22-ton Amada machines run thick turrets. If you are not certain what your press carries, send us the model and serial number and we will confirm it. See also thick vs thin turret and how Amada model numbers work.

Turret configurations for the Vipros 568

The Vipros 568 was not built with one turret. Amada offered more than one layout, so the station count does not follow from the model name — it has to be read off the machine. These are the configurations documented for this model:

A–E are Amada tool-station sizes: A ½″, B 1¼″, C 2″, D 3½″, E 4½″. A blank size column means the station and auto-index totals are confirmed but the factory A–E mix is not — we would rather leave it open than guess it.

Confirm before you quote. Because the Vipros 568 exists in more than one layout, we verify the turret from the serial number or a photograph before pricing any sleeving. If you send us the serial number we will tell you which of the above you have, and how many stations that means. Send us the serial number.

What the number tells you

Amada model numbers describe the machine. The Vipros 568 decodes as a 50-ton class press with a 60 × 80 table — the first digit is tonnage, the other two are table width and length. Its full designation is VIPROS-506080.

How to read an Amada model number — useful when your paperwork and your badge disagree.

How the Vipros 568 compares

Heaviest Vipros; 33 ton ram option — that is what sets this machine apart on the spec sheet.

These machines are easy to mix up, and the difference matters when you are quoting a turret job. Against the other Vipros models we cover:

• Amada Vipros 357 — tonnage 33 ton, control Amadan 04PC, era 1996-2003.
• Amada Vipros 358 King — tonnage 30-33 ton, control Fanuc 18P, era 1998-2003.
• Amada Vipros 2510 King — tonnage 22 ton, control Fanuc 18-PC, era 1998-2003.
• Amada Vipros 358 King II — tonnage 33 ton, control Fanuc 18P, era 1998-2003.
• Amada Vipros 358 Queen — the same on paper for turret purposes.
• Amada Vipros 345 — tonnage 30-33 ton, era mid-1990s.
• Amada Vipros 255 — tonnage 20 ton, control Fanuc 18-P, era 1995-2005.
• Amada Vipros 357 Queen — tonnage 33 ton, control Fanuc 18P, era 1999-2003.
• Amada Vipros 367 Queen — tonnage 33 ton, control Fanuc 18P, era 2001.
• Amada Vipros 368 King — tonnage 30-33 ton, control Fanuc 18P, era 1997-2005.
• Amada Vipros 368 King II — tonnage 33 ton, control Fanuc 18P, era 1999-2003.
• Amada Vipros 368 Queen — the same on paper for turret purposes.
• Amada Vipros III Z3510NT — tonnage 33 ton, control Fanuc NT, era 2003.
• Amada Vipros Z3510 Queen — tonnage 33 ton, control Fanuc 18P, era 2000s.

Sleeving is the same process across all of them. What changes is scope, and scope follows station count and how hard the machine has been run.

The Fanuc 04PC control

The Vipros 568 runs the Fanuc 04PC. Many are still serviceable and there is no reason to touch a control that is doing its job. It is worth knowing that a FANUC retrofit is available if yours becomes a problem, and that it is far cheaper done alongside turret work than as its own project later.